Xhorse Condor XC-002 PRO Cut HON66 Key Tutorial

Today we'll discuss cutting a HON66 key with Xhorse Condor XC-002 PRO. Before cutting, always make sure the key-cutting machine is well-calibrated.

Height Level Adjustment

Method 1. 

1)To start, we insert the original key with the help of a guiding block. We will use a shim to ensure the key is well-aligned.

2)Insert the key blank to the right. Now we're ready to begin height level adjustment.

3)Press down the main handle and check the indicator light. So we should just follow the direction of the light and rotate the micro-adjust knob until the middle light turns green.

Method2. 

If you don't have a shim momentarily, there is another method you can apply.

1)To ensure accuracy, we can also use probes of the same specification on both sides.

2)Press down the main handle and rotate it to lock it. And you can utilize the probe and cutter of the machine for key alignment.

3)Replace the cutter and adjust the micro-adjust knob until the middle light turns green.

Okay, now we've finished the height level adjustment of Condor XC-002 PRO.

Preparation

Before we start cutting, we need to take a look at the clamp. There are 3 marked positions at the bottom of the clamp: A, B, and C.

1. Slide in the clamp and make one triangle directs to the line depending on your need.

2. Then turn on the power switch of the cutter and adjust the speed control knob to a suitable speed.

Key Cutting

After getting everything ready, now we can start duplicating the key.

1. Press down the main handle and start cutting.

Now we've finished the one side of the key.

2. Turn off the power switch of the cutter. Clean up the clamp and flip the key.

3. Similarly, align the key and finish the height level adjustment of the other side.

4. Then turn on the switch to cut the key.

*Do not forget to turn off the power when completed.

Now we've finished the cutting and have a new HON66 key.

www.obd2shop.co.uk

Xhorse Condor XC-002 PRO Dimple Key Cutting Tutorial

This tutorial introduces how to cut a dimple key with Xhorse Condor XC-002 PRO machine step by step. 

Procedure 

1. Insert The Internal Dimple Probe & Cutter

2. Insert The Keys

Insert the original key and the blank key using a shim.

3. Select Standard Mode

Rotate the knob to standard mode.

4. Finish The Calibration

Press down the handle and finish the calibration. 

Just follow the direction of the light and rotate the micro-adjust knob until the middle light turns green. 

Make sure that the clamp is in the corresponding position.

5. Duplicate The Key

Turn on the cutter switch and press down the main handle to duplicate the key. 

Turn off the switch after finishing one side cutting. 

Flip the key and continue to cut the other side. 

After finishing one side, turn off the switch and clean up.

6. Insert The External Dimple Probe & Cutter

Replace the internal dimple probe and cutter with external ones.

7. Select Dimple Mode

Switch the knob to dimple mode.

8. Insert The Keys

9. Finish The Calibration

Clamp the keys and don't forget to complete the calibration.

10. Duplicate the key

After finishing one side, turn off the switch and clean up. Flip the key and cut the other side.

Now we've got a perfect duplicate by Condor XC-002 PRO Key Cutting Machine.

Let's give it a try, it works perfectly.

www.obd2shop.co.uk

(Fixed) VVDI PROG Read NEC3529 Prompts "Adapter invalid"

A few days ago we received a case sharing from a customer about the solution to "VVDI PROG read NEC3529 prompts 'Adapter invalid' ".

Customer's problem: I tried to read the NEC3529 using the XDNP82 adapter and the software still tells me that the adapter is invalid, look at the picture.

all contacts are ok, also on FLMD 3.3V

Later, the customer found the problem himself and successfully solved it:

Problem solved!

The adapter does not work at a voltage of 12V.

The voltage on the power supply must be at least 12.5 V.

Thanks to Jan Sima for sharing with us.

For more technical support, please follow www.obd2shop.co.uk

How to install Xhorse Multi-prog Driver on WIN7

In the previous article, we briefly introduced the Xhorse Multi-prog Programmer. Today, we will guide you on how to install the driver for your Multi-prog device upon receiving it, so you can successfully utilize it.

If you have received the Multi-prog but find that there is no response when connecting to the computer, and the software shows that the device is not connected, don't worry.

This is not a problem with the device. Likely, you haven't installed the driver yet.

If your computer is a WIN10 system, the driver will be installed automatically, so you don't have to worry about it.

However, if your computer is a WIN7 system, we need to install the driver manually.

So today I will show you how to install the driver for Multi-prog manually.

First, connect the device to the computer, then click [Help] on the top of the software interface.

Choose [Install the driver] and there will be a popup.

The device name will be automatically identified here.

If it is blank, it means that the device is not recognized and we need to re-plug the device or change the port until a multi-prog device appears here.

Then click the small arrow to find the CDC driver.

Start the installation.

Okay, we can see that the device status becomes "connected".

Please note that if the installation fails, we need to click [WIN7 Repair Driver] first, and then install the driver again.

If you encounter any problems during the installation process, please contact technical support on Xhose APP or you can contact us.

For more technical services, please pay attention to http://blog.obd2shop.co.uk/

VVDI2 + GODIAG Mech-Key Test Platform Read BMW CAS1

GODIAG BMW Mech-Key Test Platform is used for BMW CAS1/CAS2 mechanical key matching, reading, writing, and synchronization without welding. Compatible with most key programmers like Xhorse VVDI2, Key Tool Plus, etc. To program BMW semi-smart keys, we should use the GODIAG Semi Smart Test Platform.

Following we'll show how to read CAS1 data with VVDI2 + GODIAG.

1. Connect GODIAG, VVDI2 & CAS1 module.

2. Press the GODIAG START button to power it on.

3. Connect VVDI2 to the computer.

Open VVDI2 software, 

Key Learn >> CAS/EWS information >> Connect >> Read EEPROM >> OK

Reading data success.

Save the EEPROM file.

Read KM >> OK

The kilometer stored in CAS is 271905km.

Read Code >> OK

CAS code-DME: 3926

All reading success.

Insert the key into the ignition for a test.

The key is NOT ejected, which means key info is synchronized.

Key Learn >> CAS Key Learn >> Connect >> Get key info >> Add key >> OK

We can see the key has occupied the Key7 position.

Save the original key file.

Done.

www.obd2shop.co.uk

Xhorse Multi-Prog Read/Write Microcontroller Operation Guide

This is an operation guide on how to read & write Microcontroller via Xhrose Multi-Prog Programmer. Read this article carefully to learn.

Why to read & write Microcontroller?

The microcontroller function is mainly used for data reading and writing of various automotive electronic modules and automotive computer modules. It is especially suitable for automobile circuit module repair. Before using this function, you need to understand some principles and common knowledge of microcontrollers.

Multi-PROG supports reading, writing, and programming various common brands of microcontrollers. Before data reading and writing, you should make the correct wiring connections according to the software wiring diagram corresponding to the brand, model, and microcontroller series. For some models, the microcontroller requires a soldering minimum system circuit before reading.

How to distinguish Microcontroller manufacturers?

Xhorse Multi Prog device supports reading and writing microcontrollers from multiple manufacturers. Among common automotive electronic modules, the microcontroller manufacturers used include Atmel, Motorola, Freescale, Infineon, Renesas, STMicroelectronics, etc. As shown in below pic.

What's the Microcontroller memory area division?

Microcontroller usually has three storage spaces: program area, data area, and configuration area. The program area stores the program data of the microcontroller. The data area stores the information data of the microcontroller. The configuration area stores the corresponding configuration data of the microcontroller, such as the encryption byte option, the startup byte option, and so on. When reading and writing microcontroller data, it is necessary to distinguish by different areas. In software, names such as FLASH, CFLASH, CODE, and ROM are usually used to represent the program area. The names such as DFLASH, EEPROM, DATA, INF, etc. represent the data area. The names such as Config represent the configuration area. Please note that the configuration area may be unreadable for encrypted chips.

How to read & write Microcontroller?

The microcontroller option provides wiring diagrams for the basic read/write of the corresponding microcontroller. During the actual read/write process, a multimeter is necessary to find the connection diagram for the specific board, as shown in the below pic.

1)Optional(must be low): When reading this microcontroller, you must make sure that this pin of the board is low before you can read it. If it is not low, you can connect a 1K pull-down resistor to GND on this pin.

2)Pull-up resistor: This pin needs to be connected to a pull-up resistor to VCC when reading.

3)If the crystal frequency is not 4 megahertz, please connect pin 1 of the chip to the CLK output of the programmer: When reading, this pin needs to be checked whether it is necessary to connect an external clock pin for reading.

www.obd2shop.co.uk

Xhorse MQB-RH850/V850 Adapter + Key Tool Plus Read 3426 Dash

Xhorse MQB-RH850/V850 Adapter has been released for reading VW 4th Gen Johnson Controls 34xx series, MQB-RH850(R7F) series and MQB 34xx series dashboards without cutting wire or lifting pins. The adapter only supports working with VVDI Key Tool Plus currently.

In this case, we'll read the MQB 3426 dashboard as an example, which can be used for IMMO programming and mileage repair. The procedure needs to read 2 data: original chip data and EEPROM data.

Check the full video:

Tools Required

MQB 3426 dashboard

Xhorse Key Tool Plus

MQB-RH850/V850 Adapter

EEPROM adapter

DB15 cable

Step1. Read the Original Chip Data

Immo programming >> VW >> Select by type >> MQB instrument immo system >> Instrument-MQB48[VDO/JCI-NEC35xx lock] >> Start programming >> Read disclaimer, OK

*Make sure the Network connection is normal.

Programmer reads files >> Read NEC35xx/RH850 chip >> Wire bond >> D70F3426

Follow the connection diagram:

1. Remove 4 components, and add tin to solder joints.

2. Solder the MQB-RH850/V850 Cable.

3. Connect an external 5.1Ω resistor and solder the remaining parts.

Connect the adapter & Key Tool Plus, and we can start reading the original data.

Read >> Continue

Save the data file.

Step2. Read EEPROM Data

1. Remove the cable and restore the capacitors.

2. Remove the octagonal chip from the dashboard and put it in the EEPROM adapter.

Connect the adapter & Key Tool Plus, and we can start reading EEPROM data.

Programmer reads files >> Read 95128 EEPROM >> Read >> Continue

Save the EEPROM data file.

Step3. Obtain Immo Data

Obtaining immo data >> OK >> Load the original chip file & EEPROM file

Calculating... it will take about 5-10 minutes.

Reading immo data successfully.

Save data file, this can be used to generate dealer keys and key learning.

Lastly, restore the octagonal chip to the dashboard.

*Please clean the solder joints in time to ensure their cleanness. Otherwise, the normal use of the dashboard will be affected.

www.obd2shop.co.uk