Xhorse VVDI Key Tool Plus VA Version vs. Advanced Version

Xhorse has released a new VVDI Key Tool Plus VA version, focused on VAG IMMO programming like Volkswagen, Audi, Porsche, etc. What's it different from the Key Tool Plus advanced version? Here we have the comparison table.

Comparison Table

Conclusion

Xhorse VVDI Key Tool Plus VA price is half cheaper and it does not have BMW & Mercedes-Benz IMMO programming function that requires additional activation. Other than that, everything else is the same.

www.obd2shop.co.uk

Xhorse Key Tool Plus BMW MSD87 ISN Solderless Reading on Bench

Xhorse VVDI Key Tool Plus & XDNP30 Bosch ECU Adapter have been upgraded to support reading BMW ISN code on the bench. The ECU code would be very useful when programming BMW CAS3++/CAS4+ encrypted version & FEM/BDC all keys lost. Supported types covering MSV80, MSV90, MSD80, MSD81, MSD85, MSD87, N20, N55, B38, B48, B58.

This is reading BMW MSD87 no soldering on the bench as a demonstration.

How to read BMW ISN with VVDI Key Tool Plus?

Immo programming >> BMW >> Select from system >> ECU ISN >> Start programming >> BENCH read ISN - MSV90/ MSV80/MSD80/MSD81/MSD85/MSD87.etc >> MSD87

Please ensure the network connection is good. Press "Yes".

Here we can check the detailed wiring diagram.

Connect VVDI Key Tool Plus & BMW module via XDNP30 Bosch Cable.

Supply 12V to power it on.

Press "Read" and wait for a while.

Read succeeded.

Press "OK" to save the data file.

Now Key Tool Plus is showing the VIN & ISN code.

Just remember to record it.

Done.

www.obd2shop.co.uk

Xhorse Masker Garage Remote Manual: How to Delete Code and Clone Remote

Xhorse Masker Garage Remote supports code deleting, remote cloning, frequency setting, and data recovery.

And here is a tutorial on how to delete the code and clone the remote.

First, let's look at the basic structure of Masker Garage Remote:

Slide down the cover, and you can see the LED light, "Up" button, "Down" button, "Lock" button, and "Pause" button.

Next, let's do code deleting.

Before remote cloning, we need to check the status of the remote control to make sure the code has cleared.

Keep pressing any button, and the LED light is always on, which means the code has not been cleared.

Then how to delete the code?

Press and hold the "Up" and "Down" buttons at the same time, and you can see the LED light turns on.

When the light turns off, release the buttons.

Press and hold the "Pause" button until the light goes off.

Then release the button.

Now the light will flash once and then go out quickly when we press any button on the remote.

It means the code is deleted.

Then last, let's start remote cloning.

There are three steps.

Press and hold the button, and the remote will enter the cloning mode.

The LED light will flash, and then go out.

Put the original remote next to the Masker garage remote.

Then press and hold the same button on both remotes.

Once the light is on, the current button is successfully cloned.

Follow the above steps to clone all buttons one by one.

Remote cloning is successful!

You can also click on the video below to view the tutorial:

For more information about Xhorse Masker Garage Remote, please follow: 

http://blog.obd2shop.co.uk/

Solution: Xhorse Condor XC-Mini Plus II "Error Code:56"

Problem: horse Condor XC-Mini Plus II key cutting machine prompts an error code:56 "The cutter is short-circuited, please check the cutter conductivity."

How to solve it? Please help.

Solution

1. Remove those screws to take off Condor XC-MINI 2 scree.

2. Pull out the whole motor case to remove the screws on it.

3. After removing the motor case, the cable-related conductivity will expose. Please check if the cable was damaged.

4. The cable goes through the whole main motor, one side is connected to the LED bar and the other side is connected to the probe case. To remove the cable, we need to remove the cable socket, then pull it out from the bottom LED bar side.

5. Loosen the fixing screws of the conductive wire as shown. Remove the LED lamp cover.

6. Remove the 3 fixing screws, note that there are 3 black plastic parts on the screws, do not lose them.

7. Check if the 4 wires are broken or if the screws are tightened.

Hope this is helpful.

www.obd2shop.co.uk

VVDI Key Tool MAX has an error in programming XEDS01EN Super Remote

Customer Problem: When I use the VVDI Key tool max to program XEDS01EN DS Style Super Remote, I get this message:

Solution: Try to update VVDI Key Tool Max to the latest version.

Customer Feedback: It works, thanks!

To learn more about Xhorse Key Tool Max, please follow http://blog.obd2shop.co.uk/

Xhorse Dolphin XP-005 Cut VW Audi HU162T Key Tutorial

Xhorse Dolphin XP-005 Key Cutting Machine supports cutting the latest HU162T key with 9/10 bittings, such as VW Golf 7 or Audi. This is a tutorial on how to cut this particular type of key.

1. Go to Cut By Bitting >> HU162T-10/ HU162T-9

Eg. Taking cut 9 bittings as an example.

2. Decode the front 9 bittings & select B clamp first, then continue to cut this side.

3. Return to the previous page, and select 3 bittings & D clamp. This will need another HU162T key blank to fix the key firmly. Go on to decode the key, then cut the key.

That's it!

The cutting steps apply to Dolphin II as well.

(Solved) Xhorse Condor XC Mini Plus motor not spinning

Problem: My Condor XC Mini Plus, everything else works on it, the X Y Z axis also works fine and I have upgraded it to the latest version, but the motor won't spin.

Solution: Replace the driver board.

For more technical services, follow http://blog.obd2shop.co.uk/